|
Post by digiTED aka 'Ted' on Mar 1, 2013 18:20:16 GMT -7
Where can I buy the 4 bolts used to affix the amp chassis to its cab?
|
|
|
Post by Albert on Mar 1, 2013 18:22:06 GMT -7
Ask doc or hardware store...
Sent from my Desire HD using proboards
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 1, 2013 19:42:53 GMT -7
They are 1/4" #20 3.5 inch machine bolts. I have 3 (yeah,I know, not much help) left in the box that I have if you want them. PM if you do.
|
|
|
Post by aslerjack on Mar 1, 2013 20:03:22 GMT -7
Ace Hardware stores carry them.
Jack
|
|
|
Post by digiTED aka 'Ted' on Mar 2, 2013 11:40:28 GMT -7
Right on; thanks guys! And a cold virtual beer to you, ajb20002! I'll just get some locally, but huge thanks for the offer. HERE'S a link to a pack of 10 in stainless for $7 shipped.
|
|
|
Post by Ryan (shorty) on Mar 2, 2013 12:16:43 GMT -7
I wouldn't recommend stainless...too soft. Don't ask how I know.
|
|
|
Post by digiTED aka 'Ted' on Mar 2, 2013 12:21:52 GMT -7
I wouldn't recommend stainless...too soft. Don't ask how I know. Did you put anything anti-galvanic on the threads? I'm replacing some b/c the regular steel ones (galvanized?) galled a bit from some mild surface corrosion and I stripped one getting it out. I put a dab of synthetic bearing grease on the remaining ones and now there seems to be peace in the kingdom
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Mar 2, 2013 18:25:19 GMT -7
I just went to the hardware store. Take one of the old bolts with you to get the proper threads and bolt diameter.
|
|
|
Post by Ryan (shorty) on Mar 3, 2013 5:44:25 GMT -7
I wouldn't recommend stainless...too soft. Don't ask how I know. Did you put anything anti-galvanic on the threads? I'm replacing some b/c the regular steel ones (galvanized?) galled a bit from some mild surface corrosion and I stripped one getting it out. I put a dab of synthetic bearing grease on the remaining ones and now there seems to be peace in the kingdom I didn't put anything on the threads and they galled so badly I had to cut them out and retap the chassis threads. Not fun.
|
|
|
Post by digiTED aka 'Ted' on Mar 3, 2013 10:03:47 GMT -7
Did you put anything anti-galvanic on the threads? I'm replacing some b/c the regular steel ones (galvanized?) galled a bit from some mild surface corrosion and I stripped one getting it out. I put a dab of synthetic bearing grease on the remaining ones and now there seems to be peace in the kingdom I didn't put anything on the threads and they galled so badly I had to cut them out and retap the chassis threads. Not fun. OUCH. Gotta love a 10 min. task that turns into an hour LOL
|
|
tactus33
New Member
Maz 18 jr head + Z cab with Celestion Gold
Posts: 6
|
Post by tactus33 on Sept 26, 2018 11:54:31 GMT -7
For my Maz 18, here are the good sizes for screws and washers ( from Dr Z repair department): The chassis screws are stainless steel ¼-20 X 1 ¼ ” The washers are stainless steel cup washers ID 5/16” OD ¾ ”. 3 1/2 for the lenght is a bit too long Chears
|
|